deahandra glass door, 2018-02-26 12:52:13. This article is going to be about replacing an old sliding glass door with a modern Vinyl frame sliding glass door. If you currently have french doors and you want to replace them with sliding doors, or vise versa, future articles will cover that topic.
alexandria glass door, 2018-02-26 14:06:49. It seems you almost can′t build a house over 5000 SF any more without including a multi-slide door. What used to be a luxury is now almost a requirement. This being the case it appears that more and more consumers want to update their existing homes with these products. Their popularity cannot be denied so I feel the best way to discuss these doors are in terms of pro′s and cons. Then, you the homeowner can decide whether the decision is right for you or not.
betty glass door, 2018-02-26 14:04:50. The first thing we have to do is measure for the replacement door. You want to measure across the bottom, center, and top of the existing door frame to find the narrowest dimension. Start outside and measure at the point where the old door frame stops and the exterior material starts. That material can be stucco, siding, or brick. Measure across in the 3 places: bottom, center, and top. Record the smallest dimension. Then go inside and do the same thing. You want to measure where the frame ends and the drywall, plaster, or sheetrock begins. Take all six measurements, find the narrowest one, and deduct 3/4". That is the width of the new door. Now, when you measure the height, you can do it just on the outside. Measure the left, center, and right side from the ground where the bottom track sits, up to the top where the old frame ends and the exterior material begins. Take the narrowest dimension and deduct 1/2". That is your height of the new door. Then, determine which side the sliding panel should be on. The fixed panel is designated by the letter "O", and the slider is an "X". In most areas of the country, you call it out by looking at the door from outside and reading left to right. So, if you were outside looking at your door, and you want the sliding panel to close to the right wall, you would ask for an "OX". However, because i have recently discovered that not all parts of the country do it this way, my suggestion is to ask the dealer how they read the opening before placing your order.
falentino glass door, 2018-02-26 13:57:43. Another benefit of glass as a material for use in doors and partitions is that it is incredibly durable and extremely easy to keep clean. Glass does not rust, or corrode, it is not susceptible to woodworm, and it doesn′t collect dust. All that is necessary to keep the glass door or glass partition looking clean and attractive is to give it an occasional wipe with a cloth and some glass cleaner. This is ideal for both businesses and homes.
deahandra glass door, 2018-02-26 14:03:32. Your first step is to remove the the old handle and then clean the area from which you removed it. If glue or any other type of adhesive was used on the old one, make sure that any remaining matter is scraped off to allow the new door handle to be installed as smooth as possible. Next, make sure that the holes on the door itself are of equal distance with the holes on the new glass handle. If the holes match, proceed to drill in the screws. If new ones need to be drilled, mark the surface with a pencil where you wish to place the new screws. If you are installing a glass handle that does not require screws, you may use an adhesive to install the new handle. Make sure that that you use a strong water proof adhesive that will withstand heat and steam. After you′ve applied the adhesive and have installed the new glass handle, do not use the handle for several hours until the handle is firmly secured.
falentino glass door, 2018-02-26 14:07:47. With a choice of colours and many different types of frameless glass doors, including fixed, hinged, sliding and folding systems, there are many benefits worth considering, both for the home and for business environments.
betty glass door, 2018-02-26 14:06:29. Difficult to Install - This is one of the projects that I would seriously recommend you hire a licensed contractor to install. Most manufacturers only sell the product as an installed unit because of the difficulty of installing them; they require all installers to be factory trained employees. Even manufacturers that don′t install, usually require vendors to be licensed glaziers.
betty glass door, 2018-02-26 14:07:26. Once the door is on its side, you can closely examine the wheels and the track. Most commonly, you will find the wheels are full of soot and debris, and the track is also likely very dirty. To clean the wheels, use compressed air and needle tip pliers. Be careful to pull every last hair out of the wheel bearings. It is wise to be diligent in this step, so you don′t have to make a habit of this process. Once the wheels are completely clean, spray a little bit of penetrating oil into the wheel bearings, spinning the wheel as you apply the oil. (The best choice for the oil is DuPont′s Teflon non-stick dry film lubricant.) It is equally important to clean the track that the wheels rest on. Use damp paper towels to remove the grit and dirt, and then spray the penetrating oil along the track so it is well-applied. Use a clean paper towel to ensure it is evenly applied.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does youdopia claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.